View XPEBBL-L1-0000-00301_8349067.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product family data sheet copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. cld-ds56 rev 5 cree ? xlamp ? xp-e2 leds product description the xlamp ? xp- e2 le d builds on the unprecedented performance of the original xp-e by increasing lumen output up to 20% while providing a single die l e d point source for precise optical control. the xp-e2 le d shares the same footprint as the original xp -e , providing a seamless upgrade path to more lumens and/or greater effciency while shortening the design cycle for existing xp customers. xlamp xp- e2 le ds are the ideal choice for lighting applications where high light output and maximum effcacy are required, such as led retroft lamps, outdoor, portable, indoor directional, emergency vehicle or architectural. features ? available in white, outdoor white, 80-cri, 85-cri, 90-cri white, royal blue, blue, green, pc amber, amber, red-orange & red ? ansi-compatible chromaticity bins ? white binned at 85 c ? maximum drive current: 1 a ? low thermal resistance: as low as 5 c/w ? wide viewing angle: 110-135 ? unlimited foor life at 30 c/85% rh ? refow solderable - jedec j-std-020c compatible ? e lectrically neutral thermal path ? rohs-compliant ? ul-recognized component (e349212) www .cree.com/xlamp cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 table of contents characteristics .......................... 2 flux characteristics - white ........ 3 flux characteristics - color ......... 4 relative spectral power distribution ............................... 6 relative flux vs. junction temperature ............................. 7 e lectrical characteristics - white .. 8 e lectrical characteristics - color .. 8 relative flux vs. current - white . 9 relative flux vs. current - color .. 9 relative chromaticity vs. current and temperature - warm white .. 10 typical spatial distribution ......... 11 thermal design ........................ 12 refow soldering characteristics . 13 notes ...................................... 14 mechanical dimensions .............. 15 tape and reel .......................... 16 packaging ................................ 17
2 characteristics characteristics unit minimum typical maximum thermal resistance, junction to solder point - white, royal blue, blue c/w 9 thermal resistance, junction to solder point - green c/w 15 thermal resistance, junction to solder point - pc amber c/w 9 thermal resistance, junction to solder point - amber c/w 7 thermal resistance, junction to solder point - red-orange, red c/w 5 viewing angle (fwhm) - white degrees 110 viewing angle (fwhm) - royal blue, blue, green degrees 135 viewing angle (fwhm) - pc amber degrees 110 viewing angle (fwhm) - amber, red-orange, red degrees 130 temperature coeffcient of voltage - white mv/c -2.3 temperature coeffcient of voltage - royal blue, blue mv/c -3.3 temperature coeffcient of voltage - green mv/c -3.8 temperature coeffcient of voltage - pc amber mv/c -2.5 temperature coeffcient of voltage - amber, red-orange, red mv/c -1.8 esd withstand voltage (hbm per mil-std-883d)- white, royal blue, blue, green v 8000 esd classifcation (hbm per mil-std-883d) - pc amber, amber, red-orange, red class 2 dc forward current ma 1000 reverse voltage v 5 forward voltage (@ 350 ma, 85 c) - white v 2.9 3.25 forward voltage (@ 700 ma, 85 c) - white 3.05 forward voltage (@ 1000 ma, 85 c) - white 3.15 forward voltage (@ 350 ma, 25 c) - royal blue, blue v 3.1 3.5 forward voltage (@ 1000 ma, 25 c) - royal blue, blue v 3.4 forward voltage (@ 350 ma, 25 c) - green v 3.2 3.8 forward voltage (@ 1000 ma, 25 c) - green v 3.7 forward voltage (@ 350 ma, 25 c) - pc amber v 3.05 3.5 forward voltage (@ 1000 ma, 25 c) - pc amber v 3.28 forward voltage (@ 350 ma, 25 c) - amber, red-orange, red v 2.2 2.6 forward voltage (@ 1000 ma, 25 c) - amber, red-orange, red v 2.65 le d junction temperature c 150 copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
3 flux characteristics (t j = 85 c) - white the following table provides several base order codes for xlamp xp- e2 le ds. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. for more order codes, as well as a complete description of the order-code nomenclature, please consult the xlamp xp family leds binning and labeling document. color cct range base order codes min. luminous flux (lm) @ 350 ma calculated minimum luminous flux (lm)** @ 85 c order code min. max. group flux (lm) @ 85 c flux (lm) @ 25 c* 700 ma 1.0 a cool white 5000 k 10,000 k q4 100 116 171 218 xpebwt-l1-0000-00c51 q5 107 124 183 233 xpebwt-l1-0000-00d51 r2 114 132 195 249 xpebwt-l1-0000-00e51 r3 122 142 209 266 xpebwt-l1-0000-00f51 outdoor white 4000 k 5300 k q4 100 116 171 218 xpebwt-01-0000-00cc2 q5 107 124 183 233 xpebwt-01-0000-00dc2 r2 114 132 195 249 xpebwt-01-0000-00ec2 r3 122 142 209 266 xpebwt-01-0000-00fc2 neutral white 3700 k 5300 k q4 100 116 171 218 xpebwt-l1-0000-00ce4 q5 107 124 183 233 xpebwt-l1-0000-00de4 r2 114 132 195 249 xpebwt-l1-0000-00ee4 80-cri white 2200 k 4300 k q2 87.4 101 150 191 xpebwt-h1-0000-00ae7 q3 93.9 109 161 205 xpebwt-h1-0000-00be7 warm white 2200 k 3700 k q2 87.4 101 150 191 xpebwt-l1-0000-00ae7 q3 93.9 109 161 205 xpebwt-l1-0000-00be7 q4 100 116 171 218 xpebwt-l1-0000-00ce7 85-cri white 2600 k 3200 k p2 67.2 78.0 115 147 xpebwt-p1-0000-007e7 p3 73.9 85.7 127 161 xpebwt-p1-0000-008e7 p4 80.6 93.5 138 176 xpebwt-p1-0000-009e7 q2 87.4 101 150 191 xpebwt-p1-0000-00ae7 90-cri white 2600 k 3200 k p2 67.2 78.0 115 147 xpebwt-u1-0000-007e7 p3 73.9 85.7 127 161 xpebwt-u1-0000-008e7 p4 80.6 93.5 138 176 xpebwt-u1-0000-009e7 notes: ? cree maintains a tolerance of 7% on fux and power measurements, 0.005 on chromaticity (ccx, ccy) measurements and 2 on cri measurements. ? typical cri for cool white (5000 k C 10,000 k cct) is 70. ? typical cri for neutral white (3700 k C 5300 k cct) is 75. ? typical cri for outdoor white (4000 k - 5300 k cct) is 70. ? typical cri for warm white (2200 k C 3700 k cct) is 80. ? minimum cri for 80-cri white is 80. ? minimum cri for 85-cri white is 85. ? minimum cri for 90-cri white is 90. * flux values @ 25 c are calculated and for reference only. ** calculated fux values at 700 ma and 1 a are for reference only. copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
4 flux characteristics (t j = 25 c) - color the following table provides several base order codes for xlamp xp- e2 color le ds. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. for more order codes, as well as a complete description of the order-code nomenclature, please consult the xlamp xp family leds binning and labeling document. color minimum radiant flux @ 350 ma dominant wavelength range order codes, group flux (mw) min. max. group dwl (nm) group dwl (nm) royal blue 30 450 d3 450 d5 465 xpebry-l1-0000-00j01 31 475 d3 450 d5 465 xpebry-l1-0000-00k01 32 500 d3 450 d5 465 xpebry-l1-0000-00l01 33 525 d3 450 d5 465 xpebry-l1-0000-00m01 34 550 d3 450 d5 465 xpebry-l1-0000-00n01 35 575 d3 450 d5 465 xpebry-l1-0000-00p01 color dominant wavelength range base order codes min. luminous flux (lm) @ 350 ma order code min. max. group dwl (nm) group dwl (nm) group flux (lm) blue b3 465 b6 485 k2 30.6 xpebbl-l1-0000-00y01 k3 35.2 xpebbl-l1-0000-00z01 m2 39.8 xpebbl-l1-0000-00201 m3 45.7 XPEBBL-L1-0000-00301 color dominant wavelength range base order codes min. luminous flux (lm) @ 350 ma order code min. max. group dwl (nm) group dwl (nm) group flux (lm) green g2 520 g4 535 q2 87.4 xpebgr-l1-0000-00a01 q3 93.9 xpebgr-l1-0000-00b01 q4 100 xpebgr-l1-0000-00c01 q5 107 xpebgr-l1-0000-00d01 r2 114 xpebgr-l1-0000-00e01 r3 122 xpebgr-l1-0000-00f01 note: ? cree maintains a tolerance of 7% on fux and power measurements and 1 nm on dominant wavelength measurements. copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
5 color color bin base order codes min. luminous flux (lm) @ 350 ma order code group flux (lm) pc amber y2 q2 87.4 xpebpa-l1-0000-00a01 q3 93.9 xpebpa-l1-0000-00b01 q4 100 xpebpa-l1-0000-00c01 color dominant wavelength range base order codes min. luminous flux (lm) @ 350 ma order code min. max. group dwl (nm) group dwl (nm) group flux (lm) amber a2 585 a3 595 n4 62.0 xpebam-l1-0000-00601 p2 67.2 xpebam-l1-0000-00701 p3 73.9 xpebam-l1-0000-00801 p4 80.6 xpebam-l1-0000-00901 color dominant wavelength range base order codes min. luminous flux (lm) @ 350 ma order code min. max. group dwl (nm) group dwl (nm) group flux (lm) red- o range o3 610 o4 620 p2 67.2 xpebro-l1-0000-00701 p3 73.9 xpebro-l1-0000-00801 p4 80.6 xpebro-l1-0000-00901 q2 87.4 xpebro-l1-0000-00a01 q3 93.9 xpebro-l1-0000-00b01 q4 100 xpebro-l1-0000-00c01 color dominant wavelength range base order codes min. luminous flux (lm) @ 350 ma order code min. max. group dwl (nm) group dwl (nm) group flux (lm) red r2 620 r3 630 n3 56.8 xpebrd-l1-0000-00501 n4 62.0 xpebrd-l1-0000-00601 p2 67.2 xpebrd-l1-0000-00701 p3 73.9 xpebrd-l1-0000-00801 note: ? cree maintains a tolerance of 7% on fux and power measurements and 1 nm on dominant wavelength measurements. flux characteristics (t j = 25 c) - color (continued) copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
6 relative spectral power distribution relative spectral power 0 10 20 30 40 50 60 70 80 90 100 380 430 480 530 580 630 680 730 780 relative radiant power (%) wavelength (nm) cool white warm white relative spectral power 0 20 40 60 80 100 380 430 480 530 580 630 680 730 780 relative radiant power (%) wavelength (nm) royal blue blue green pc amber amber red - orange red copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
7 relative flux vs. junction temperature (i f = 350 ma) relative flux output vs. junction temperature 0 20 40 60 80 100 120 25 50 75 100 125 150 relative luminous flux (%) junction temperature (oc) white relative flux output vs. junction temperature 0 10 20 30 40 50 60 70 80 90 100 25 50 75 100 125 150 relative radiant flux (%) junction temperature (oc) royal blue relative flux output vs. junction temperature 0 10 20 30 40 50 60 70 80 90 100 25 50 75 100 125 150 relative luminous flux (%) junction temperature (oc) blue green pc amber amber red - orange, red copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
8 electrical characteristics (t j = 85 c) - white electrical characteristics (t j = 25 c) - color electrical characteristics (tj = 25oc) 0 100 200 300 400 500 600 700 800 900 1000 2.7 2.8 2.9 3.0 3.1 3.2 forward current (ma) forward voltage (v) white electrical characteristics (tj = 85oc) 0 100 200 300 400 500 600 700 800 900 1000 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 forward current (ma) forward voltage (v) royal blue, blue green pc amber amber, red - orange, red copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
9 relative flux vs. current (t j = 85 c) - white relative flux vs. current (t j = 25 c) - color relative intensity vs. current (tj = 85oc) 0 50 100 150 200 250 0 100 200 300 400 500 600 700 800 900 1000 relative luminous flux (%) forward current (ma) white relative intensity vs. current (tj = 25oc) 0 50 100 150 200 250 0 100 200 300 400 500 600 700 800 900 1000 relative radiant flux (%) forward current (ma) royal blue relative intensity vs. current (tj = 25oc) 0 50 100 150 200 250 300 0 100 200 300 400 500 600 700 800 900 1000 relative luminous flux (%) forward current (ma) blue green pc amber amber red - orange, red copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
10 relative chromaticity vs. current and temperature - warm white* * warm white xlamp xp- e2 le ds have a typical cri of 80. relative chromaticity vs. current, ww - 0.020 - 0.015 - 0.010 - 0.005 0.000 0.005 0.010 0.015 0.020 0 100 200 300 400 500 600 700 800 900 1000 current (ma) ccx ccy t j = 85 c relative chromaticity vs. temperature ww - 0.020 - 0.015 - 0.010 - 0.005 0.000 0.005 0.010 0.015 0.020 0 20 40 60 80 100 120 140 160 tsp ( c) ccx ccy i f = 350 ma copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
11 typical spatial distribution typical spatial radiation pattern 0 20 40 60 80 100 - 90 - 70 - 50 - 30 - 10 10 30 50 70 90 relative luminous intensity (%) angle ( ) white typical spatial radiation pattern 0 20 40 60 80 100 - 90 - 70 - 50 - 30 - 10 10 30 50 70 90 relative luminous intensity (%) angle (o) royal blue, blue, green pc amber amber, red - orange, red copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
12 thermal design the maximum forward current is determined by the thermal resistance between the l e d junction and ambient. it is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics . white royal blue, blue green amber pc amber red-orange, red 0 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w thermal design - royal blue - same as blue 0 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w thermal design - amber 0 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w thermal design - green 0 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 20 c/w rj - a = 25 c/w rj - a = 30 c/w rj - a = 35 c/w thermal design - red-orange, red 0 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w thermal design - pc amber 0 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
13 reflow soldering characteristics in testing, cree has found xlamp xp-e2 leds to be compatible with jedec j-std-020c, using the parameters listed below. as a general guideline, cree recommends that users follow the recommended soldering profle provided by the manufacturer of solder paste used. note that this general guideline may not apply to all pcb designs and confgurations of refow soldering equipment. profle feature lead-based solder lead-free solder average ramp-up rate (ts max to tp) 3 c/second max. 3 c/second max. preheat: temperature min (ts min ) 100 c 150 c preheat: temperature max (ts max ) 150 c 200 c preheat: time (ts min to ts max ) 60-120 seconds 60-180 seconds time maintained above: temperature (t l ) 183 c 217 c time maintained above: time (t l ) 60-150 seconds 60-150 seconds peak/classifcation temperature (tp) 215 c 260 c time within 5 c of actual peak temperature (tp) 10-30 seconds 20-40 seconds ramp-down rate 6 c/second max. 6 c/second max. time 25 c to peak temperature 6 minutes max. 8 minutes max. note: all temperatures refer to topside of the package, measured on the package body surface. copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
14 notes lumen maintenance projections cree now uses standardized i e s lm-80-08 and tm-21-11 methods for collecting long-term data and extrapolating led lumen maintenance. for information on the specifc lm-80 data sets available for this led, refer to the lm-80 results document . please read the long-term lumen maintenance application note for more details on crees lumen maintenance testing and forecasting. please read the thermal management application note for details on how thermal design, ambient temperature, and drive current affect the l e d junction temperature. moisture sensitivity in testing, cree has found xlamp xp-e2 leds to have unlimited foor life in conditions 30 oc/85% relative humidity (rh). moisture testing included a 168-hour soak at 85 oc/85% rh followed by 3 refow cycles, with visual and electrical inspections at each stage. cree recommends keeping xlamp l e ds in their sealed moisture-barrier packaging until immediately prior to use. cree also recommends returning any unused l e ds to the resealable moisture-barrier bag and closing the bag immediately after use. rohs compliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the product documentation sections of www.cree.com . ul recognized component level 4 enclosure consideration. the led package or a portion thereof has been investigated as a fre and electrical enclosure per ansi/ul 8750. vision advisory claim warning: do not look at exposed lamp in operation. e ye injury can result. for more information about le ds and eye safety, please refer to the led e ye safety application note . copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
15 mechanical dimensions all measurements are .13 mm unless otherwise indicated. anode anode size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 r 1.53 .65 .73 3.30 .50 2.30 3.30 1.30 2.26 1 / 1 22.000 a 2610-00029 outline drawing xpe g2 07/19/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 r 1.53 .65 .73 3.30 .50 2.30 3.30 1.30 2.26 1 / 1 22.000 a 2610-00029 outline drawing xpe g2 07/19/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 r 1.53 .65 .73 3.30 .50 2.30 3.30 1.30 2.26 1 / 1 22.000 a 2610-00029 outline drawing xpe g2 07/19/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 r 1.53 .65 .73 3.30 .50 2.30 3.30 1.30 2.26 1 / 1 22.000 a 2610-00029 outline drawing xpe g2 07/19/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 r 1.53 .65 .73 3.30 .50 2.30 3.30 1.30 2.26 1 / 1 22.000 a 2610-00029 outline drawing xpe g2 07/19/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) bottom view side view top view recommended pcb solder pad recommended stencil pattern hatched area is opening copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
16 tape and reel all cree carrier tapes conform to eia-481d, automated component handling systems standard. all dimensions in mm. loaded pockets (1,000 lamps) leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) start end cathode side anode side (denoted by + and circle) 160.0 a a b 2.5 .1 section a-a scale 2 : 1 1.5 .1 8.0 .1 4.0 .1 1.75 .10 12.0 .0 + .3 detail b scale 2 : 1 13 mm 7" cover tape pocket tape user feed direction user feed direction 13 61 12.40 0 + 2.00 measured at hub 12.40 measured at inside edge 16.40 sheet 1 of 1 1:2 2400-00005 size title rev. c drawing no. date date date check final protective finish material approved drawn by third angle projection .x 0.3 x 2 .xx .10 .x .25 for sheet metal parts only .xx .13 x 1 unless otherwise specified dimensions are in millimeters & before finish. tolerance unless specified: scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 361-4770 4600 silicon drive durham, n.c 27703 notice cree confidential. this plot and the information contained within are the proprietary and confidential information of cree, inc. this plot may not be copied, reproduced or disclosed to any unauthorized person without the written consent of cree, inc. reel, 7" x 12mm wide b liudezhi 2012/5/25 +/- 0.5 ps 190 ????1? ??e (c) by foxit software company, 2004 foxit pdf editor ?- od 7.5'' 13 61 12.40 0 + 2.00 measured at hub 12.40 measured at inside edge 16.40 sheet 1 of 1 1:2 2400-00005 size title rev. c drawing no. date date date check final protective finish material approved drawn by third angle projection .x 0.3 x 2 .xx .10 .x .25 for sheet metal parts only .xx .13 x 1 unless otherwise specified dimensions are in millimeters & before finish. tolerance unless specified: scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 361-4770 4600 silicon drive durham, n.c 27703 notice cree confidential. this plot and the information contained within are the proprietary and confidential information of cree, inc. this plot may not be copied, reproduced or disclosed to any unauthorized person without the written consent of cree, inc. reel, 7" x 12mm wide b liudezhi 2012/5/25 +/- 0.5 ps 190 ????1? ??e (c) by foxit software company, 2004 foxit pdf editor ?- od 7.5'' y y x x ref 0.59 w f(iii) p1 d1 1.5 min. bo ao r 0.2 typical ref 4.375 ko other material available. (iv) (iii) (ii) (i) hole to centerline of pocket. measured from centerline of sprocket holes is 0.20. cumulative tolerance of 10 sprocket to centerline of pocket. measured from centerline of sprocket hole section y-y section x-x 2.0 0.05 (i) p2 1.55 0.05 do 4.0 0.1 (ii) po 1.75 0.1 e1 0.30 0.05 t ref r 2.24 2.40 ko +0.0/-0.1 3.70 1 w f p +/- 0.05 +/- 0.1 +0.3/-0.1 5.50 8.00 12.00 ao 3.70 +/- 0.1 bo +/- 0.1 y y x x ref 0.59 w f(iii) p1 d1 1.5 min. bo ao r 0.2 typical ref 4.375 ko other material available. (iv) (iii) (ii) (i) hole to centerline of pocket. measured from centerline of sprocket holes is 0.20. cumulative tolerance of 10 sprocket to centerline of pocket. measured from centerline of sprocket hole section y-y section x-x 2.0 0.05 (i) p2 1.55 0.05 do 4.0 0.1 (ii) po 1.75 0.1 e1 0.30 0.05 t ref r 2.24 2.40 ko +0.0/-0.1 3.70 1 w f p +/- 0.05 +/- 0.1 +0.3/-0.1 5.50 8.00 12.00 ao 3.70 +/- 0.1 bo +/- 0.1 y y x x ref 0.59 w f(iii) p1 d1 1.5 min. bo ao r 0.2 typical ref 4.375 ko other material available. (iv) (iii) (ii) (i) hole to centerline of pocket. measured from centerline of sprocket holes is 0.20. cumulative tolerance of 10 sprocket to centerline of pocket. measured from centerline of sprocket hole section y-y section x-x 2.0 0.05 (i) p2 1.55 0.05 do 4.0 0.1 (ii) po 1.75 0.1 e1 0.30 0.05 t ref r 2.24 2.40 ko +0.0/-0.1 3.70 1 w f p +/- 0.05 +/- 0.1 +0.3/-0.1 5.50 8.00 12.00 ao 3.70 +/- 0.1 bo +/- 0.1 cathode side anode side copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds
17 packaging patent label (on bottom of box) label with cree bin code, qty, reel id label with cree bin code, qty, reel id label with cree order code, qty, reel id, po # label with cree order code, qty, reel id, po # label with cree bin code, qty, reel id unpackaged reel packaged reel boxed reel cree bin code & barcode label vacuum-sealed moisture barrier bag label with customer p/n, qty, lot #, po # label with cree bin code, q t y , lot # label with cree bin code, q t y , lot # v acuum - sealed moisture barrier bag p atent label label with customer order code, q t y , r eel i d , po # copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? xp-e2 leds

▲Up To Search▲

Price & Availability of XPEBBL-L1-0000-00301

	To Download XPEBBL-L1-0000-00301 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .